Remote useeTV untuk mengontrol Televisi (TV)

Untuk yang sudah memasang Indihome, berikut trik yang cukup berguna agar tidak ribet dengan banyak nya remote untuk mengontrol TV dan Receiver (STB) useeTV yaitu ZTE ZXV10 B700V5.

Daripada menggunakan remote bawaan TV untuk mengontrol TV, maka akan jauh lebih efisien untuk menggunakan 1 remote untuk 2 perangkat yaitu useeTV dan TV dirumah.

Prosesnya :
1. Posisikan 2 remote saling berhadapan IR_LED-nya, dgn jarak antara 10cm s/d 20cm,
jangan terlalu dekat karena resiko error (akibat noise) lebih besar
2. (usee) tekan+tahan tombol SET tunggu sampe indikator berubah dari merah menjadi hijau, lepaskan
3. (tv) tekan tombol Power, indikator (usee) berubah jadi merah, tandanya sinyal IR tv sudah diterima
4. (usee) tekan tombol Power sesaat, indikator menjadi hijau lagi. di sini code Power udah disave.
5. (tv) tekan tombol Vol+, indikator (usee) berubah jadi merah, tandanya sinyal IR tv sudah diterima
6. (usee) tekan tombol Vol+ sesaat, indikator menjadi hijau lagi. di sini code Vol+ udah disave.
7. (tv) tekan tombol Vol-, indikator (usee) berubah jadi merah, tandanya sinyal IR tv sudah diterima
8. (usee) tekan tombol Vol- sesaat, indikator menjadi hijau lagi. di sini code Vol- udah disave.
...pairing....done.....
9. (usee) tekan tombol SET sesaat:
- jika indikator langsung mati: all done
- jika indikator jadi merah, berarti dia menangkap sinyalnya sendiri, gpp, coba ulangi lagi aja.

Kadang remote useeTV salah save code, sehingga ditest ga jalan. ulangi lagi aja step1 s/d 9.
Apabila tombol Power udah ok, tapi tombol Vol+/Vol- gak bener, gpp ulangi lagi aja tapi hanya untuk tombol itu aja. misal hanya Vol- yg gk bener, maka langkah" di atas cukup: 1, 2, 7, 8, 9.
1. Posisikan 2 remote saling berhadapan IR_LED-nya, dgn jarak antara 10cm s/d 20cm
2. (usee) tekan+tahan tombol SET tunggu sampe indikator berubah dari merah menjadi hijau, lepaskan
7. (tv) tekan tombol Vol- bbrp kali, indikator (usee) berubah jadi merah, tandanya sinyal IR tv sudah diterima
8. (usee) tekan tombol Vol- sesaat, indikator menjadi hijau lagi. di sini code Vol- udah disave.
9. Tekan tombol SET



Credit to : nabilracer@kaskus

About Blue Screen Of Death (BSOD)

Below is the common message that appear when Our Computer in problems.. most of people call it Blue Screen Of Death (BSoD).. there is 10 message that appear when we had BSoD

1. IRQL_NOT_LESS_OR_EQUAL (0X0000000A)
This is the most case that we usually found in most of the computer problems.. this fault message shows when there is unmatched driver on the computer
The Cause:
? Driver problem such as driver clash or unmatch driver
? Video Card Problems, usually when we upgrade our Video Card, we forgot to Uninstall the old Video Card Driver
? Audio Card, because the configuration fault or bug in driver sound card


2. NTFS_FILE_SYSTEM atau FAT_FILE_SYSTEM (0X00000024) atau (0X00000023)
This message pointing us to check all around the harddisk, this include the partition (with chkdsk tools) or maybe its because the cable of the harddisk

3. UNEXPECTED_KERNEL_MODE_TRAP (0X0000007F)
The Cause of this message is:
? Overclock Hardware that too much over the ability of the Hardware
? Overheating components
? Corrupted BIOS
? Fault Memory and CPU

4. DATA_BUS_ERROR
There is a possibility that a memory or memory slot on the motherboard had some problems

5. PAGE_FAULT_IN_NONPAGED_AREA
Sometimes its because the Hardware Fault, Include primary memory, video card memory, or Processor memory (L2 Cache)

6. INACCESSIBLE_BOOT_DEVICE
there is problems on Harddisk jumper configuration, Virus Boot Sector, wrong IDE driver Controller, or Chipset Driver fault

7. VIDEO_DRIVER_INIT_FAILURE
This because of the uncompleted installation of the video card driver, restart in the middle of installation or maybe its because there is bug on the driver installation

8. BAD_POOL_CALLER
This can happen because of driver fault or uncompatible driver.. mostly when we upgrading the XP installation

9. PEN_LIST_CORRUPT
This message appear because of the RAM fault

10. MACHINE_CHECK_EXCEPTION
This because the CPU overclock over the limit, or because the power supply problems

How To Repair Windows (Damaged Windows)

Windows Repair

1. Fixing Installation (Repair Install)

If Your Windows XP corrupted and You don't have any operating system for booting, you can do Installation Repair (Repair Install), that will make Your Computer back to working as it like a fresh copy of Windows XP.

* You make sure that you have a Valid Windows XP Key

* Entirely processes will spend time more or less a half or 1 hours, depends on Your computer.

* If You asked to type the Administrator Password, You must choose the Second Repair Option that appear secondly.. not the first Repair Option that appear

* Insert Your Windows XP CD and does booting from that CD.

* When the Second Repair Option appear.. press R = Repair, this will began the Repair Installation

* Press F8 to agree the next process “ I Agree At The Licensing Agreement ”.

* Press R while Windows XP to the installed Windows XP directory. Usually “C:\WINDOWS” then it will copy the files to the drive C. then it will be auto-restarting when it done.. just let the CD on the CD-ROM drive

* Next You will see a Progress Bar that become a part of the Installation Progress.. then a message like “Collecting Information, Dynamic Update, Preparing Installation, Installing Windows, Finalizing Installation” shows up.. choose NEXT

* You will be asked to insert the key.. (Your Windows XP Key that valid)

* Your normally want to stay at the same domain name or same Workgroup.

* Your Computer will be restart. Then You will have same display as it were system activation just like the normal installation.

* Register if You want it (usually doesn't be required). All through.

2. NTOSKRNL Corrupted Or Missing :

If You got some error message that “ NTOSKRNL Not Found ”

* Insert Windows XP CD and booting from that CD.

* When first Repair Option is appear press R button..

* type a number that suitable to your XP Installation Directory that appear on the screen.. usually number 1..

* Move to the CD Drive's (e.g: E)

* type: CD i386

* type: expand ntkrnlmp.exc:\Windows\System32\ntoskrnl. exe

* If Your Windows XP are installed else where, juts change to its location.

* Eject Your CD and type EXIT.

3. HAL.DLL Damaged or Lost (Missing or Corrupt)

If You get an error message that wrecks or a loss file HAL.DLL, maybe its because a false comfiguration of file BOOT.INI (misconfigured).

* Insert Your Windows XP CD and booting from that CD.

* When first Repair Option is appear press R button..

* Type a number that suitable to your XP Installation Directory that appear on the screen.. usually number 1..

* type: bootcfg / list In function to feature content / entry on BOOT.INI file.

* type: bootcfg / rebuild In function to fix configuration of BOOT.INI'S file.

* Eject Your CD and type EXIT.

4. Directory \WINDOWS\SYSTEM32\CONFIG Corrupted or get Lost

If You get error message:

” Windows could not start because the following files is missing or corrupt : \WINDOWS\SYSTEM32\CONFIG\SYSTEM or \WINDOWS\SYSTEM32\CONFIG\SOFTWARE”

* Insert Your Windows XP CD and booting from that CD.

* When first Repair Option is appear press R button..

* Type a number that suitable to your XP Installation Directory that appear on the screen.. usually number 1..

* Insert Administrator Password if necessary.

* type: CD \windows\system32\config.

* Next depends on which part that had a damage.

* type: ren software software.broken OR ren system system.broken

* next again also depending to the part that had a damage.

* type: copy \windows\repair\system

* type: copy \windows\repair\software

* Eject the CD and type EXIT.

5. NTLDR or NTDETECT.COM not Found

If You get Error Message like as above:

FAT Partition

Please do booting from Your Windows98 Boot Disk and copy the NTLDR or NTDETECT.com from your i386 direcory to the root of drive C:\

NTFS Partition

* Insert Your Windows XP CD and booting from that CD.
* When first Repair Option is appear press R button..
* Type a number that suitable to your XP Installation Directory that appear on the screen.. usually number 1..
* Insert Administrator Password if necessary.
* Insert following instruction, where x: is of Your CD-ROM Drive (Suiting To Your Drive).

* type: COPY x:\i386\NTLDR C\:

* type: COPY x:\i386\NTDETECT. COM C:\

* Eject Your CD and type EXIT